Kicker ZX100.2 User Manual Page 2
- Page / 4
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
+12V
18"
+
_
+
_
+
_
(45cm)
24"
(60cm)
+
_
+
_
XOVER
XOVER
XOVER
KUNEK
10 - COMA
Installation
1. Mounting Choose a structurally sound location to mount your Kicker amplifi er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least
4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled
passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to
mount the amplifi er.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to
the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low
level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er,
the ZX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the
source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the
RCA Inputs on the end panel of the amplifi er as shown in Figure 1. Keep the audio signal cable away
from factory wiring harnesses and other
power wiring. If you need to cross this
wiring, cross it at a 90 degree angle.
Install one 15 ampere fuse within 18” (45cm) of the battery and in-line with the 8 gauge power cable
connected to your amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been
installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as
when you installed it.
3. Confi guration The following diagrams show the most common confi gurations for your Kicker ZX
series amplifi er.
ZX.2SeriesAmplifi er
Owner’sManual
TwoChannelModel: ZX100.2
Authorized Kicker Dealer:
Purchase Date:
Amplifi er Model Number:
Amplifi er Serial Number:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
__________________________
__________________________
__________________________
__________________________
INSTALLATION
2
ZX.2AMPLIFIER
CONFIGURATION
3
KUNEK
10 - COMA
+12V
18"
(45cm)
24"
(60cm)
4
"
c
m)
+12V
18"
(45cm)
24"
(60cm)
KUNEK
10 - COMA
Figure 2
Figure 3
Figure 4
Minimum Impedance of 2 ohms per channel in stereo operation
Minimum impedance of 4 ohms while in bridged operation
Minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously
Ground
Remote
Turn-On
Fuse
Battery
High Pass
High Pass
Low Pass
Signal In
Source Unit
Ground
Remote
Turn-On
Fuse
Battery
Ground
Remote
Turn-On
Fuse
Battery
R+
R-
Signal In
Signal In
Source Unit
Source Unit
Bridge Wiring
Bridge Wiring
Bridged Operation (Mono)
Two Channel Operation (Stereo)
Stereo and Mono Operation Simultaneously (SAMS)
Note: To get the best performance from your new Kicker Amplifi er, we recommend using genuine Kicker Accessories and Wiring.
L+
L-
R+
R-
L+
L-
R+
R-
L+
L-
Performance
Model ZX100.2
RMS Power in Watts, all channels driven @14.4
Volts, 4Ω stereo, ≤ 1% THD+N
25 x 2
@ 2Ω stereo, ≤ 1% THD+N 50 x 2
@ 4Ω mono, ≤ 1% THD+N 100
Length: in(cm) 8 1/4 (20.9)
Specifi cations common to all models:
Height: in(mm) 2 1/8 (54mm)
Width: in(mm) 9 5/8 (244mm)
Frequency Response, ± 1 db: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95db, a-weighted, re: rated power
Input Sensitivity:
Low Level: 125mV-5V
High Level: 250mV-10V
Selectable Electronic Crossover:
12 db/Octave High Pass Fixed @ 80Hz
12 db/Octave Low Pass Fixed @ 80Hz
Bass Boost: Variable 0 to +12dB Bass Boost @ 40Hz
+
+
>
+
>
Core Cable
Ground or Shielding
High-level Speaker Output Wire
To Amplifi er
To Source Unit
Figure 1
Remote
Turn-On
Related products and manuals for Car amplifier Kicker ZX100.2
Car amplifier Kicker ZX2500.1 EU User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 1.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals