Kicker 2015 PX Mono Amplifiers Owner's Manual download pdf (Page 2)

PXA.1-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁ er. Make sure there are no items

behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open

ventilation for the ampliﬁ er. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the

ampliﬁ er.

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the PXA harness to the

ampliﬁ er. A good ground connections is important. If this ampliﬁ er is mounted in the front fairing of a motorcycle, it

will be best to extend the ground wire all the way to the battery.

The PXA ampliﬁ ers have the capability to receive almost any level of input signal. If a Hi-Level signal is coming

from the speaker leads of the source unit, simply cut off the RCA jacks and connect it directly to the exposed

wires. Set the Input Level switch to Hi. Set the Auto Turn-On to DC. If speaker leads are not available from your

source unit, use an RCA stereo cable to connect directly to the RCA connectors of the PXA ampliﬁ er. Set the

Input Level switch to Lo. Set the Auto Turn-On switch to +12V, and use the blue remote trigger wire to turn the

ampliﬁ er on.

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Serial Number:

Model: PXA200.1 PXA500.1

RMS Power [Watts]

@ 14.4V, 4Ω mono, ≤ 1% THD+N

@ 14.4V, 2Ω mono, ≤ 1% THD+N

@ 14.4V, 1 mono, ≤ 1% THD+N

@ 14.4V, 0.5 mono, ≤ 1% THD+N

25 x 1

50 x 1

100 x 1

200 x 1

250 x 1

500 x 1

N/A

Length [in, cm] 4-3/4, 12 8-1/4, 21

Height [in, cm] 1-9/16, 4 1-9/16, 4

Width [in, cm] 3-7/16, 8.7 3-7/16, 8.7

Frequency Response [Hz] 25 - 120 25 - 120

Signal-to-Noise Ratio [dB] 95 95

Input Sensitivity Low Level: 125mV–5V

High Level: 250mV–10V

Low Level: 125mV–5V

High Level: 250mV–10V

Electronic Crossover Selectable 60Hz, 80Hz, 100Hz or

120Hz low pass; 24dB/octave slope

Selectable 60Hz, 80Hz, 100Hz or

120Hz low pass; 24dB/octave slope

KickEQ™ Bass Boost Selectable 0 or +6dB @ 40Hz Selectable 0 or +6dB @ 40Hz

Subsonic Filter 25Hz, 24dB/octave slope 25Hz, 24dB/octave slope

Remote Bass Yes Yes

Pro Tip: To get the best performance from your new KICKER Ampliﬁ er and extend the warranty by 1 year, use

genuine KICKER accessories and wiring.

MODEL: PXA200.1 | PXA500.1

IMPORTANT SAFETY WARNING –

PROLONGED CONTINUOUS OPERATION OF

AN AMPLIFIER IN A DISTORTED OR CLIPPED

MANNER CAN CAUSE YOUR AUDIO SYSTEM

TO OVERHEAT, POSSIBLY CATCHING FIRE

AND RESULTING IN SERIOUS DAMAGE TO

YOUR COMPONENTS AND/OR VEHICLE.

2015 PX Mono Amplifiers Rev D.indd 22015 PX Mono Amplifiers Rev D.indd 2 8/26/2014 3:42:37 PM8/26/2014 3:42:37 PM

1 2 3 4 5 6 7 ... 19 20

Comments to this Manuals

No comments

Kicker 2015 PX Mono Amplifiers Owner's Manual Page 2

Comments to this Manuals

Related products and manuals for Loudspeakers Kicker 2015 PX Mono Amplifiers